Since ancient times, the Russian bath has been a favorite place for water procedures. The only drawback of the bath buildings was considered to be cool floors, which were made of wood and even earthen. As is known from the law of physics, warm air from a stone stove immediately rises, heating the room, but the floors remain cold. It is this temperature difference that leads to an uncomfortable state of a person while taking bath procedures.
Walking on a cold floor causes not only discomfort, but can also lead to a cold, especially in children. Therefore, an attentive owner is thinking about how to make a warm floor in a bathhouse from a stove with his own hands. Fortunately, modern industry offers many materials that can facilitate such construction.
Features of a warm floor
Since the bath is considered a room with high humidity and temperature, the materials used to make warm from the stove must effectively resist rotting and the harmful effects of water.
For the manufacture of flooring, various types of tiles, as well as natural stone or porcelain stoneware, are best suited. These materials have a high heat transfer and are completely unaffected by high humidity. Laying the warm floor in the bath from the stove is carried out on tile adhesive, which has high waterproofing properties.
Many homeowners still dream of a warm natural wood floor that feels good on the feet, but requires a lot of effort to maintain and install. Under the action of moisture, the wood gets wet and expands, and a microclimate is created at the junctions, which contributes to the development of mold. Therefore, the manufacture of a warm floor in a bath from a simple stove is recommended to be made from coniferous trees, as they contain a large amount of oils that increase the resistance of the material to water, which prevents the wood from rotting.
But when looking for the best coating option, it is better to opt for ceramic floor tiles. Such material has a high degree of thermal conductivity and is several times more efficient than wood. Stone floors also look great, which transfer heat as well as tiles. That's just the process of cleaning the premises will present a certain difficulty, but it depends on the choice of stone.
Benefits of using heating
The main advantage, the preservation of the health of people who take it, has already been mentioned. To date, there are still a number of positive reviews about the warm field in the bath from the stove:
- The underfloor heating system is considered absolutely harmless to human health and environmentally friendly.
- Unlike electric heating, the warm floor in the bath from the stove can fully boast of the absence of electromagnetic radiation, which adversely affects the well-being of a person.
- The use of heating from the stove contributes to the creation of a comfortable microclimate in the bathhouse.
- An important role is played by the low cost of fuel for heating and its low consumption.
Of course, skeptics may say that it is difficult to mount such a structure. But these difficulties will more than pay off in further operation.
Disadvantages of floor heating system
However, along with many positive qualities, there are some disadvantages of using a water-heated floor in a stove bath:
- During the cold period, the heating circuit may freeze, and this may lead to damage to the pipes. Therefore, it is necessary to drain the coolant or heat it constantly, which is economically unprofitable. You can also use antifreeze instead of water.
- Decrease in the efficiency of the furnace, due to the need to spend its thermal energy on heating the storage tank. This disadvantage applies to both the washing department and the steam room.
- An increase in the warm-up time in several rooms of the bath building at once.
- The impossibility of installing leaking floors, as wetting the thermal insulation can lead to a decrease in the efficiency of the entire heating system.
Floor installation methods
Before starting construction work on installing a warm floor in a bath from a stove with your own hands, you need to decide on the option for its manufacture.
Using modern materials, you can lay a heated coating in the following ways:
- The installation of a heating system in the wooden floors of the bath room will require the builder to make an accurate calculation of the places where the log is cut for laying heating pipes. The advantage of a wooden coating is the possibility of repair work.
- The best option for a warm floor in a bath from a stove is the manufacture of a concrete screed, which has a high degree of moisture resistance and a low cost of the materials used. It should only be noted that the operation of such a coating is possible after a certain period of time necessary for the complete drying of the screed. It will also be quite difficult to determine the location of a pipeline leak if it is damaged.
- The use of special polystyrene sheets, which have a foil reflective layer and the necessary recesses for reliable fastening of the pipe system, has become possible with the development of the construction industry. It is worth noting that such a coating still needs to be poured with a concrete screed.
The principle of floor heating from the stove
To make a warm floor in the bath from the stove, you need to make a metal shirt that looks like a skeleton from a longitudinal pipe with several outlets. Such outlets are connected at the bottom by tubes, closing into a heating system. The shirt is installed above the furnace, inside the furnace.
If the floor heating system in the bath is from a stove without a pump, then the water circulates due to the temperature difference of the heated carrier. It is very difficult to create conditions for the natural movement of water; it is necessary that the furnace and the buffer tank, which is installed outside the heat source, be located at least in the same plane. Therefore, the device of a warm floor in a bath from a stove with forced convection is a more common way to create water circulation.
The purpose of the buffer tank
The buffer tank is an indispensable part of the heating system, as it eliminates the boiling of water in the jacket. It is installed immediately after the coil in the coolant system. Natural circulation of water is possible only if the entire boiler room system is located below the floor level in the bath. Such an arrangement is economically unprofitable, therefore, forced movement of water using a circulation pump is more often used.
It is considered very practical to create a warm floor in the bath from the Termofor stove, since the design of this device has a built-in metal shirt. The technological process of heating, based on the use of this furnace, consists in the correct connection of the boiler to the heating system.
Substrate preparation for underfloor heating
Before proceeding with the laying of pipes for heating, it is necessary to perform basic preparatory work. These technological operations include the preparation of the underfloor heating base, as well as the organization of the drainage of water from the bathhouse.
If the heated floor will be installed on open ground, then it is necessary first of all to level the surface, with the creation of a slope to remove water. Then you need to do the following:
- Remove excess soil between the walls of the foundation of the building. Lay the sewer pipe, then tamp the surface.
- Backfill with a mixture of sand and gravel up to 15 cm high. Compact this pillow.
- Then, it is desirable to insulate the surface with a layer of fine expanded clay with a thickness of 15-20 cm.
The next step is to insulate the base to avoid heat loss during floor heating.
Wooden floor insulation
Thermal insulation of a wooden surface is carried out in the following sequence:
- load-bearing beams are installed on the bottom, to which bars are attached, which serve as the basis for the vapor barrier;
- then a draft floor is created from unedged boards;
- insulation is laid between the beams;
- on top of the insulation material it is necessary to lay a layer of waterproofing;
- the next step will be the installation of pipes for heating;
- this entire structure is covered by a basic floor covering.
concrete flooring process
Here the task looks much more difficult than with a wooden coating. All warming operations are as follows:
- the base for the floor, after making the foundation, is made of a concrete screed or floor slab;
- then a waterproofing layer of roofing material is laid on this base;
- on top of this layer, a foam polystyrene insulation is installed;
- a special mesh for reinforcement is laid on the insulation and this layer is poured with cement mortar.
Experienced builders advise before laying the roofing material to fill the surface with bituminous mastic to prevent moisture from penetrating.
Heating pipe laying schemes
Thermal conductors are laid with a snake or snail. In rooms with a large area, the method of arranging pipes with a snail will be the most effective, since with this method there is no temperature loss. The serpentine laying option is mainly used in rooms up to 10 m 2.
To compensate for heat loss, a reduction in the laying step is used. So, if the standard step is 30 cm, then the second half of the room is passed with a step of 20 cm, and the last quarter - 15 cm. This principle will allow you to maintain the required temperature of the coolant.
The volute laying method has the advantage that it is not necessary to bend the tube 180°, as with serpentine laying, but 90° or even a circular pattern is sufficient.
Regardless of which system was chosen, all operations must be performed strictly according to the technological process. In this case, the main attention should be paid to the requirements of safety and comfort of using the bath room.
Now, in many dachas and in their homes, there is still stove heating, but due to the peculiarity of heating as such, the floors in the house are almost always cold.
In this article, we will improve the heating system and combine the stove with a water-heated floor.
Warm floor from the stove
Bringing the project to life
In order to make warm floors that are connected to the heating system, you need to fulfill a number of factors.
First of all, this system must include a circulation pump. The system itself can be designed for one pipe or two.
If the room is large, and you cannot fit in this number, then you will need to make several contours.
Preparing the floor
In order not to waste heat and heat the floor slabs in vain, it is necessary to prepare the base before installing the system.
1. If the floor is covered with tiles, parquet or something else, then this coating must be removed. Then inspect the cement and, if necessary, grout the joints with cement and level the floor surface with cement mixed with coarse sand.
2. We install a damper tape along the perimeter of the floor at the junction of the walls and the floor (it is needed to maintain the screed when temperatures change).
Keep in mind that the width of the tape must be greater than the width of the concrete screed. It can be fixed if the walls are even on an adhesive base, if not uneven - on dowel-nails.
3. Then you need to put a solid thermal insulation, such as extruded polystyrene in the form of plates or rolled polyethylene foam with a foil coating.
4. An ordinary plastic film is laid on top (so that the concrete does not leak).
5. After that, plastic guides are laid, and on them a metal mesh with cells from 10 cm.
The floor under the stove with laying the water circuit and pouring the screed
After we have prepared the floor, we need to lay and fix the polyethylene pipes for water.
It is better to lay it with a “snail” (as shown below), this creates fewer corners and does not distribute space into “cold and hot zones”.
Interesting! What to make the floors in the house.
Pipes are laid with a distance 15cm(if you have a warm climate - then 30cm).
Decide for yourself if you need to make the floor warmer - take a smaller step, even on a certain piece of the floor.
Subsequence:
1. Pipes are laid exactly according to the plan, starting from the distribution point, besides leaving a little distance for connecting pipes.
It is better to do the laying together: one lays, the second fixes to the grid.
2. After the preliminary layout (so far without fixing), the pipes are brought to the distributor and fixed.
3. The connection is made using a connecting bundle to the distributor. After fixing, the system is filled with water (check for damage).
4. Now the final part is carried out - concrete screed (fine-grained concrete 200 is suitable for this).
First, beacons are placed and fixed, then they are poured with concrete (concrete should cover pipes and fittings to a height of 6 cm). Not hardened concrete is leveled with a rule (a long wooden plank).
5. A flat surface should be moistened for 3-4 weeks or a film should be laid on top so that the concrete gradually dries out and does not crack.
6. After the final hardening, you can proceed to the decorative coating.
Any kind of decorative coating can be laid on top of the cement, a flat surface only contributes to this.
Thus, you have not only a warm, but also a beautiful design of your floor, on which children will play freely, and you will be calm for them.
Video Do-it-yourself water-heated floor
Bath procedures have always had a special status among our people, a bath is a favorite place for water procedures from ancient times to the present day. If earlier the only drawback of a good bath was a cool floor, today such an inconvenience is eliminated quite simply by making a warm floor in the bath. Many qualified construction professionals give practical advice on how to make a warm floor in a bath. If desired, the procedure can be entrusted to a professional team of craftsmen, or you can do everything yourself, exactly following the proven instructions.
In addition to being unpleasant to walk on cold floors, it can cause colds, especially in young children, and also creates a high percentage of excessive fuel consumption, which is spent on heating the bath rooms reserved for the necessary procedures. In order to avoid such problems, it is important to tackle the problem of floor insulation at the design stage, choosing the most successful option for your bathhouse.
Tip number 1. It is necessary to make a warm floor in the bath in all the constituent rooms, that is, in addition to the steam room, heating should be installed both in the room reserved for rest and in the washing room.
Floor covering for such structures is of two types, namely:
- Concrete base floors.
- Wooden base floors.
Based on this classification, there are also varieties of methods for creating a warm floor in a bath with your own hands. It is worth noting that the general specifics of the process are carried out according to a similar algorithm, but still, some stages of the warming procedure may differ. It depends on what specific heating is chosen for the coating. Before creating a warm floor, the coating itself in the bath should be insulated in advance; the following building materials can be used for this:
- Special wool of basalt or mineral sample.
- Expanded clay substance.
- Different types of foam plastic with dimensions from 5 cm thick.
Wooden floor insulation in the bath room
Measures for the thermal insulation of wooden flooring in the bathhouse start with the removal of the finish, in cases where the insulation is carried out on an already finished building, and is not carried out during its construction. Further, the installation of underfloor heating in the bath is carried out in the following sequence:
- Special beams are mounted on the bottom, to which special bars are fixed, which will later serve as the basis for the vapor barrier.
- A rough coating is created on top, for which boards are used.
- In the space between the beams, the previously selected insulation material should be laid.
- On the insulation you need to lay a waterproofing layer under the floor.
- The completed structure is closed with clean boards, which will serve as the main floor covering.
Council number 2. Builders advise creating a floor covering in a bathhouse based on softwood lumber, which does not slip when wet, lasts longer, and also has a smell that has a beneficial effect on the overall health of the body. Do not use materials based on oak, poplar or linden.
Insulation of the concrete floor in the bath room
Creating a warm floor in a bath with a concrete coating is a much more difficult task in comparison with a wooden bath. Here the procedure has some differences and is performed in the following sequence:
- After creating the foundation for the future building under the bath, it is covered with a concrete slab.
- A layer of waterproofing material is carefully laid on such a base, as a rule, euroroofing material is used, which has high strength characteristics, but at the same time its installation does not cause difficulties even for an inexperienced person.
- On top of the mentioned material, it is already necessary to lay the insulation itself, for a concrete floor polystyrene foam is preferable, but expanded clay (fine fraction) is also allowed.
- The insulation is followed by a special reinforcing mesh, which is later filled with a special mortar based on concrete with the addition of sand. Such a screed should be perfectly even, after it hardens, a ceramic tile of your chosen sample is laid on top.
Tip number 3. Before using euroroofing material, it is better to apply a coating waterproofing composition, this will help minimize the possibility of moisture penetration into the finished screed and make the floor more durable.
Creating a warm floor with a stove
In earlier periods in the baths, the floor was heated from a special stove-heater, or even from a stove. It is much easier to create a warm floor in a bathhouse from a stove than similar options based on water or electrical systems. To do this, a stove-heater is being built in the room, you can learn about the construction procedure of which from the attached video
Tip number 4. In order to keep the heat indoors for a longer period, the floor in the washing room should be 15 centimeters lower than the floor in the steam room. And in the rest room, the floor is 3 centimeters lower compared to the level of the same washing room.
How to create an electric floor heating in the bath
In addition to warming the floor covering, it will be useful to think over its additional heating. One of these types is considered to be an electric heated floor in a bath, the system of which is created by installing special cables that supply electricity. It is mounted above the heat-insulating layer, where either special mats or the cables themselves are laid. For uniform heating of the upper surface, the cable must be laid with the same pitch. In the concrete coating, the electric heated floor in the bath is mounted directly into the reinforced mesh.
Council number 5. In addition to insulating the flooring, it is also important to insulate the surface of the walls of the bath room. This will significantly reduce heat loss inside the building during bath procedures.
Creating a water warm coating
Among several options for creating a warm coating, it is worth noting separately the water-heated floor in the bath. This heating is carried out by a pre-installed piping system in which warm water circulates. It is quite difficult to create such a warm floor, therefore, without proper experience, it is better to invite specialists. Compared to similar insulation of an electrical sample, this floor heating system has a number of advantages. For example, you can make a water-heated floor in a bathhouse from a stove, which will reduce fuel consumption when heating rooms for water procedures.
Heated floors among all heating systems are very popular these days, due to their technical characteristics. For some residential buildings, you have to purchase electrical systems, but the owners of solid fuel stoves are more fortunate, since they can equip water contour heating.
Underfloor heating from stove heating in a wooden house is a great way to make the room temperature more comfortable and evenly distribute it over the entire area. The element that heats the heat carrier, in a specific embodiment, is a furnace, and there is no need to install a boiler.
Features of the floor heating system with water from the stove
A heat exchanger must be installed directly above the furnace, because the furnace will act as a heating element. For these purposes, an ordinary metal tank or welded pipes are suitable. It is from him that the system of water floor heating in all rooms will be laid.
Based on the fact that it will not work to mount a large-capacity heat exchanger in an ordinary stove, it will be necessary to build a storage tank next to the stove, which is connected to the heat exchanger. To exclude heat from the room through the base of the floor, foil thermal insulation is laid on it, which effectively reflects energy and helps to normalize the temperature.
In addition, you will need a pump to return the chilled liquid back to the heating tank. The only exception is stoves that are below floor level.
Attention! The auxiliary pump is installed on the common return, and not on the cycle that does not warm up well. If you install the pump separately on any of the wings, then the water will circulate in a small circle.
The normal temperature for a warm floor is 40 ° C, and a brick oven, unlike a specialized boiler, does not have an automatic regulator, so the indicators can differ significantly from the norm. Therefore, in addition to the circulation pump, it will be necessary to install a mixing unit.
If it is necessary to install several circuits for different rooms, a collector is mounted between the boiler and the floor surface, to which valves with thermal heads and two- or three-way valves are connected in order to freely regulate the operation of the system.
Advantages and disadvantages of the system
A warm water floor in a wooden house under a screed from the stove is characterized by the following advantages:
- Fuel economy, ease of maintenance and installation.
- The contour is mounted inside the screed without reducing the usable area.
- Environmental friendliness.
- High heat transfer at relatively low energy costs.
- Uniform heating of the room, no cold zones.
- The possibility of heating several rooms at once from one boiler or stove.
- Long service life.
The disadvantages of the system include the following points:
- For rooms with a large quadrature, a large volume of coolant is required, so it will take a lot of time to heat it up.
- If a wooden house is located outside the city and is used as a summer residence, and not for permanent residence, then it is imperative to drain the water before leaving, otherwise frozen water can break pipes during severe frosts.
Tip: To protect the system from freezing, you need to use polyethylene pipes and pour water into them with the addition of antifreeze. They should be laid at a distance of 20-25 cm so that there are no warm and cold areas.
Types of device and materials used
The layout of the warm floor from the stove in a wooden house can be carried out in several ways:
- On a concrete screed - this is the cheapest, most reliable and moisture resistant method. With it, you can reduce the cost of building materials and work does not require practical experience. The negative qualities of this method include the duration of the process - the floor becomes ready for use only a month after pouring. In addition, if the pipeline is damaged, it will be problematic to determine the location of the leak without dismantling the entire coating.
- On a coupler with use of the polystyrene plates having factory ready dredging for fixing of heating pipes. They are distinguished by ease of installation and a reflective layer of foil material to retain heat.
- On a wooden base. Laying on logs is considered the most time-consuming process, requiring accurate calculation of the locations of holes for laying the pipeline. On the other hand, the maintainability of such floors is much higher.
Tip: The height of the insulating layer (mineral wool, expanded clay, expanded polystyrene or polystyrene) should be 15-20 cm - this factor depends on the climatic conditions of the region.
The device of a warm water floor from a stove in a wooden building
Water floor heating consists of the following layers:
- Waterproofing. It prevents condensation from settling on the structure.
- The thermal insulation layer prevents heat from escaping from the room through the bottom.
- Reinforced mounting mesh to protect insulation materials.
- A layer of thick foil to reflect heat.
- A pipeline laid out in a snake or spiral for uniform heating of the surface.
- Screed for alignment.
- Finish coating.
In some cases, when it is necessary to lay the floor directly on the ground, a “cushion” of gravel and sand is compacted in front of the waterproofing layer and an expanded clay layer is poured. This is necessary to create additional thermal insulation conditions.
Heating system installation
Any work on laying a warm floor, like other options, should begin with the preparation of a rough surface. It must be cleaned of old worn coatings, tamped or sanded to bring it to a perfectly even condition. The difference of the base in one room in height should not be more than 0.2 cm.
After preparation, you should start laying the heating pipeline:
- To begin with, as a waterproofing, roofing material is laid out in two layers perpendicular to one another. The joints of the sheets are carefully glued with mastic.
- The second step is to lay the thermal insulation material and cover it with a mesh.
- Pipes are laid directly on top of the grid.
After connecting the pipes to the system and checking it for faults, the screed is poured. For this, a cement mortar with reinforced fiberglass or diluted ready-made dry mixes is usually used.
The screed is evenly poured and leveled. Cement during the drying process may slightly change its volume, therefore, to prevent deformation of the finished coating around the perimeter of the room, a damper tape should be glued before pouring.
After complete hardening (the drying process lasts about thirty days), you can start laying facing materials.
The method of floor heating using water from the stove is a simple method that, with the right approach and following all the recommendations, will save money on the purchase of a heating boiler and electricity costs.
What is a warm floor and how convenient it is today is known to everyone. Is it a bathroom or bedroom. What if you make a warm floor in the bath from the sauna stove?
Collapse
Such a design exists and has long established itself from the most positive side. This does not require any additional electricity. Water acts as a heat carrier, and it is heated by ... a stove.
Pros and cons of installation
This design has the following advantages:
- electromagnetic radiation will not have its negative impact, which is inevitable when using electrical energy;
- this design is completely safe for the environment;
- helps to heat the room more evenly;
- saving resources;
- fungus and mold do not receive a favorable environment for reproduction;
- there is no risk of drafts, because the entire steam room is heated evenly.
Let's move on to the disadvantages:
- the bath is not heated all the time and there is a risk of pipes freezing, which can lead to failure of the entire system, so there is a need to drain water from it every time;
- the heat exchanger consumes a lot of energy that it takes from heating, therefore, if there is no proper power reserve, the room may take longer to heat up;
- the volume and time of water heating will depend on how many adjacent rooms need to be heated;
Before construction
We will give some simple tips that will help you build a similar system at home with your own hands. Such a system fully justifies itself if the stove is fired with wood.
The choice of floor design
Experts recognize the concrete screed as the optimal material for the floor in the bath. The benefits are:
- cement has high moisture resistance;
- simplicity of the device;
- cheap materials.
Flaws:
- the breakdown can be eliminated only after complete dismantling;
- otherwise it is impossible to localize the place of the accident.
In addition to concrete, you can use a wooden floor structure. Holes in the lags are provided in advance in order to carry out the necessary communications. This design, unlike concrete, will make it easy to carry out repairs without dismantling the entire floor.
Warming
To prevent heat loss, the design of the warm floor must be carefully insulated. For this, polystyrene plates are used. Special internal gutters will allow you to make the installation as convenient as possible, and the metallized coating will reflect heat back into the room.
Other nuances
- Irregularities and distortions of the floor will not matter if you make a rough screed.
- Condensate will not accumulate if a layer of waterproofing is laid.
- All energy will be directed to the room and heat loss is maximally excluded, thanks to the thermal insulation layer.
- Thermal insulation will be protected by a mesh for reinforcement.
- Thermal energy will not be lost due to the metallized substrate.
- The snail arrangement system will ensure optimal heating of the heating circuit.
- The slope to the drain must be provided by arranging a finishing screed. Slope control is carried out using the building level.
- Decorative coating will give the floor a finished look. Any material that is not contraindicated in the underfloor heating system can be used.
System Features
Due to the heat exchanger installed above the furnace, hot water will enter the system, cool down in the process of passing through it and return already cold again to the heat exchanger. There, the sauna stove with floor heating will heat it up again and the whole process will be repeated.
A small circulation pump will help us return the chilled water back to the heat exchanger. Due to the circulating energy of the coolant, uniform heating of the room will be carried out.
You will have to lay a pipe with a diameter of at least 24 mm, which will reduce the resistance when the coolant moves. As a standard, for the system, a pipe with a diameter of 16 mm is used, but this will not work for us.
The heating system provides for the use of a coolant with a temperature not higher than +40 0 C. We will need to cool the water to the desired temperature, since almost boiling water will come out of the heat exchanger, the temperature of which impossible to regulate.
Installation scheme
Manufacturing instructions
Now let's look at how to complete each step with your own hands. It is almost similar to the design in the house, but it also has its own specifics. Step-by-step instruction:
Operating rules
Operation does not require much effort. It is enough to follow a few simple rules:
- During winter, drain the system every time.
- The operating pressure in the system must be constant.
- Malfunctions in the operation of the pump and valves must be eliminated in time.
Alternatives
Electric and infrared heated floors can serve as a good alternative to a water-heated floor. Let's analyze them in more detail.
Electric underfloor heating
Similar in essence to water floors. The electric heating cable that replaces the heating circuit is the main distinguishing feature of these floors. All other processes proceed in the same way.
The system requires the installation of an additional machine and thorough waterproofing. On the other hand, a heating circuit gasket, a pump and a heat exchanger are not required. If in the previous case we did not have additional costs (with sufficient boiler power) for operation, then we will have to pay a lot for electricity.
There are two types of heating cable: with one core and with two.
The benefits are:
- the floor is easy to manufacture;
- a water circuit for heating will cost more;
- installation of such a heating system does not take much time;
- The thermostat allows you to easily set the desired heating temperature.
Minus: high energy consumption for heating.
Such a system can be used not only in the bath, but also for underfloor heating in the house.
Infrared heated floors
The existing bath room raises the feasibility of implementing a water-heated floor into a big question. In this case, the infrared floor comes to the rescue. It does not require the removal of the old coating. A thin film with a heater is easy to lay on any base. The device of the final screed in the bath room is also not necessary.
The most durable, safe and economical solution would be a water heated floor. This is when it comes to building from scratch. In an existing sauna, an infrared floor is the most optimal solution.
When choosing an underfloor heating system in a sauna room, you should take into account the material of the floor covering, the planned costs and the desired durability.
With an electric floor, not everything is so simple. Electricity tariffs in each region are different. Somewhere it will come in handy. This design is especially relevant in the case of using an electric heater.
In this case, additional power consumption for underfloor heating will not be a problem, since you still have to provide for an additional 380V line. And its advantages can be used to the full.
Choosing which option to use is not so easy. Each of them will have its advantages in one situation and disadvantages in another. Only based on the specific situation, you can make the right choice.
←Previous article Next article →